TL;DR: Too long, Didn’t read
The Golden Rule: Whether you have a smart meter or a standard meter, always read the numbers from left to right, and completely ignore any numbers in red or anything after a decimal point.
Electricity vs Gas: Electricity usage is always displayed in kilowatt-hours (kWh). Gas is displayed in cubic metres (m3) on newer meters, or cubic feet (cu ft) on older standard meters.
Smart Meter Buttons: If your smart meter screen is blank, you usually need to press ‘9’ on a keypad, or cycle through the ‘A’ or ‘B’ buttons to wake it up and find the reading.
Consumer Right: If your smart meter loses its connection (goes “dumb”), your supplier will estimate your bills. Submitting manual readings is the only way to ensure you are charged accurately for what you actually use.
There is a massive surge in UK energy customers receiving unexpectedly high bills because their energy supplier is relying on “estimated” meter readings.
When your smart meter loses its connection to the network – or if your indoor In-Home Display breaks – your supplier stops receiving automated data. If you don’t step in and provide a manual reading, they will guess your usage, which often results in severe overcharging.
Whether you have a confusing smart meter with unmarked buttons, an older digital screen, or a traditional dial meter, you have a legal right to an accurate bill. Here is exactly how to read every type of gas and electricity meter in the UK to ensure you only pay for the energy you actually use.
How to Read a Smart Meter (Electricity)
Most electricity smart meters look like a white box with a small digital screen and a few physical buttons. To get your reading, you need to navigate the screen menu to find the letters IMP KWH.
Smart Meters with a Keypad (e.g., Secure brand meters)
Press the number ‘9’ on the keypad.
Wait a few seconds for the screen to load.
The letters ‘IMP KWH’ will appear, followed by a row of numbers.
Write down the numbers from left to right. Ignore any numbers after the decimal point.
Smart Meters with ‘A’ and ‘B’ Buttons
Press the ‘A’ button to wake up the screen.
Continue pressing the ‘A’ button repeatedly until the screen displays ‘TOTAL ACT IMPORT’ (or ‘TOU RATE 1’ if you are on a single-rate tariff).
Write down the number displayed before ‘KWH’.
Smart Meters with Green and White Buttons
If you are on a standard single-rate tariff:
Press and hold the white ‘B’ button for two seconds to wake the screen.
When the screen shows ‘Meter Boost’, press the green ‘A’ button to select “No”.
Your reading will appear next to ‘KWH’.
If you are on an Economy 7 (two-rate) tariff:
Press the green ‘A’ button to wake the screen.
Press it again until you see ‘Rate 01 Act Imp’. This is your night/off-peak reading.
Press it once more to see ‘Rate 02 Act Imp’. This is your day/peak reading.
How to Read a Smart Meter (Gas)
To conserve battery life, gas smart meters are designed to go to sleep. The screen will usually be completely blank when you look at it.
Gas Meters with a Keypad
Press the number ‘9’ on the physical keypad.
The word ‘VOLUME’ will appear on the screen.
Wait a few seconds, and the screen will display a row of numbers followed by ‘m3’.
Write down the numbers from left to right, ignoring any digits after the decimal point.
Gas Meters with ‘A’ and ‘B’ Buttons
Press the ‘A’ button to wake up the screen.
Press ‘A’ again until the screen displays ‘Meter Index’.
Write down the number shown, ignoring any numbers after a decimal point.
Gas Meters with ‘Left’ and ‘Right’ Buttons (or an unmarked circle)
Press the right-hand button (or the middle circle button) to wake the screen up.
You should see a screen that says ‘Consumption in m3’ or ‘Credit ON’.
The large number displayed is your reading.
How to Read a Standard (Non-Smart) Electric Meter
If you haven’t upgraded to a smart meter yet, you will have one of these older mechanical or digital units.
Standard Digital Meters
These have an electronic or mechanical display showing a single row of numbers.
Read the numbers from left to right.
Write down the first 5 numbers shown in black or white.
Ignore the last number if it is in red, and ignore any numbers after a decimal point.
Standard Dial Meters
These look like a series of small clock faces. They are notoriously tricky to read.
Read the dials from left to right (ignore any large red dial, or any dial marked 1/10).
If the pointer is pointing directly at a number, write that number down.
If the pointer is between two numbers, always write down the lower number (e.g., if it is between 4 and 5, write down 4).
The only exception: If the pointer is between 9 and 0, write down 9.
How to Read a Standard Gas Meter
Standard gas meters come in two variations: Metric and Imperial.
Metric Gas Meters (Displaying ‘m3’)
Read the numbers from left to right.
Write down the first 5 numbers.
Completely ignore any numbers shown in the red section.
Imperial Gas Meters (Displaying ‘cu ft’)
Read the numbers from left to right.
Write down the first 4 numbers.
Ignore any numbers shown in red.
Frequently Asked Questions
If pressing the keypad or the ‘A’ and ‘B’ buttons does not wake the screen up, the physical meter may be faulty or have a dead internal battery (very common in gas meters). You must contact your energy supplier immediately. They have a regulatory obligation to repair or replace a broken meter for free, as they cannot bill you accurately without it.
No. A red flashing light on a smart meter is completely normal. It simply indicates that energy is currently being used in the property. The faster the light flashes, the more electricity you are drawing from the grid at that exact moment.
If your manual reading is significantly lower or higher than the supplier’s automated estimate, their system may flag it as an “implausible reading” and reject it. If this happens, you must call their customer service team and offer to send them a date-stamped photograph of the physical meter face to prove your reading is accurate.
We are not energy suppliers. This guide explains how to manually navigate UK smart meter and standard meter hardware to ensure accurate billing under Ofgem consumer rules. If your meter is faulty or you are disputing an estimated bill, raise a formal complaint with your supplier, followed by the Energy Ombudsman.
